METSO TSE7X20-TD

METSO

TSE7X20-TD

1299/SNTSE24068

Occasion

1522

EQUIPMENT ON LEASE METSO 7x20 THREE-DECK HORIZONTAL SCREEN The new triple shaft Metso horizontal screen is designed for maximum efficiency and performance Coil Springs and dampers 3/8” Thick Side Plates with Huck Bolt Construction Side Tension decks with seal strips for 4’ screen panels Heavy Duty Tube Steel Decks with Herringbone Cross Bracing Vibrating Mechanism (190mm bearings) with Oil lubrication Carriage Bolts used to retain clamp bars – Standard is 4’ long bars AR lined Feedbox and AR lined Discharge Lip Right hand variable speed drive standard with motor mount and belt guard and tensioning device Hand access on triple deck screens. Spray Bar knockouts, bottom deck Feed end curtain Side tension single crown Medium Scalper Deck – includes heavy duty side tension top deck, heavier feedbox liner and heavier top discharge lip. Also includes side extension wear liners along the screens sides and feedbox perimeter. Media not included Side tension single crown Media not included Side tension Media not included Motor 50HP – 60Hz/3Ph/460V – 1200RPM Installation Angle 0° Elliptical stroke 5/8” -3/4” RPM 675-875 Separating G Force: 4.8-6.5 Top deck Middle deck Bottom deck The TSE Series screens are a horizontal screen that utilize elliptical motion vibration for superior accuracy and efficiency in compact installations. They are built for stationary and portable applications in both tertiary and primary screening and can be equipped for wet or dry screening. Improved Performance With High-Power Elliptical Vibration The elliptical motion of the screens, along with high acceleration, allows for more power than in traditional screens. This feature delivers higher throughput and screening efficiency. TSE Series screens have a 1:3 elliptical ratio. This very aggressive 1:3 ratio causes vibration of the layer of materials in two directions. It also generates faster stratification of the layer so that fines pass through the screening mesh quickly and efficiently. These characteristics contribute to the TSE Series screens superiority in processing very sticky or clay materials and materials with high content of flaky particles. Designed For The Toughest Applications The body of TSE Series screens is extremely strong, supporting the stresses required by the “high power” mechanism. This robustness is provided by frames made from heavy tube cross members with stiffeners positioned in critical areas. The side plates are huck bolted without any welding. The standard drive arrangement for the TSE Series screens is a V-belt drive. The screens are equipped with a spring-tension motor base to maintain constant belt tension, thereby reducing maintenance and extending the life span of the drive components. The mechanical parts located inside the screens are fully protected by a rubber-lined steel guard with ports to allow any dust or debris that enters the counterweight area to fall free from any moving parts. The triple shaft mechanism is comprised of 6 individual bearing and bearing housings assemblies with bolt on weights that are complemented with plug weights. The six individual assemblies are synchronized with gears which create the stroke direction as well as the elliptical motion. The bearing assemblies are locked together to ensure matching stroke from side to side. Modular Machine Design Enables Flexibility The ability to make mechanical adjustments allows you to adjust all screening parameters in order to adapt them to all types of applications. Depending on the application, the vibration amplitude can be adjusted by adding or removing unbalanced weights bolted to the counterweights. If necessary, the synchronized gears can be set in various positions, changing the vibration angle. For standard vibration, the angle is set at 45° to correspond to the normal feed speed of materials, but it is possible to adjust it to between 30° and 60°. GREYHAWK PORTABLE SCREEN PLANT CHASSIS MAIN CHASSIS Main frame constructed of wide flange structural steel beams Tandem axle with (8) 11x22.5 radial tires Complete air brake system LED side marker and tail lights Fifth wheel hitch Catwalk around the sides and feed end of the screen DISCHARGE CHUTES Roll away chute (Manual) Constructed of 1/4" Mild Steel with 1/4” stitch welded AR Liners Top deck can discharge over the kingpin, or to either cross conveyor (4 blending gates) Middle deck discharges onto front or rear cross conveyor (4 blending gates) Bottom deck discharges onto rear cross conveyor SIDE DISCHARGE CROSS CONVEYOR-30” (QTY 2) Formed channel main frame 10” Van Der Graaf motorized pulley 10” x 32” tail pulley, wing style CEMA C – 5” dia. 20 deg troughing idlers CEMA C – 5” dia. Return idlers Dodge bearings Manual screw take-ups Belting - 2 ply, 3/16" x 1/16" 220 PIW Belt splice - steel mechanical fasteners Fully skirted with rubber flashing Scraper-Superior Exterra REAR DISCHARGE UNDERSCREEN CONVEYOR-60” Formed channel main frame 12” head pulley, CF with 3/8” HB lagging 12” tail pulley, wing style CEMA C – 5” dia. 20 deg picking idlers CEMA C – 5” dia. Return idlers Motor-20HP 1800RPM 230/460/3ph Gear reducer-Master PT shaft mount Shafts - turned and polished Dodge bearings Manual screw take-ups Belting - 3 ply, 3/16" x 1/16" 220 PIW Belt splice - steel mechanical fasteners Fully skirted with rubber flashing Scraper-Superior Exterra HYDRAULICS 13HP Honda Hydraulic Power Unit (4) Leveling jack legs CONTROL PANEL NEMA 4 enclosure NEMA SQUARE D electrical components 50 HP screen motor 10 HP cross conveyors (Reversing) 20 HP rear discharge underscreen conveyors Qty 3-Aux. #2 starters Hour meter Warning horn Labelled start/stop pushbuttons and E-stop pushbutton mounted on door of electrical panel Mounted on skid frame with lifting eyes SAFETY/GUARDING We install all standard guarding, customer will be responsible for compliance with local codes. GENERAL: Paint Sandblasted Two-part epoxy primer Two-part urethane topcoat Chassis Color-GH Beige Handrail/Guarding Color-GH Orange Decals-Orange & grey striping (1) sets of owners/parts manuals